V6 EXTREME AMBER DRL 7507 + PARKING - RESISTOR FREE
As low as $218.00
PER KITIn stock
YEAR WARRANTY
DESIGNED IN USA
Description
Added Visibility The Amber Extreme DRL is the most advanced LED turn signal system on the market. The unique design allows you to add a bright amber daytime running light or a safe functioning output if your car or truck uses the turn signal as the DRL. The issue with most plug-in style LED bulbs is that the output in DRL mode is not very bright, or they run too hot, overheat, and fail. Error-free bulbs generally use a thermally regulated output circuit, which reduces current to save the bulb from burning up. The problem with the design is that the current is lower, which triggers the flasher to double the flash rate because it thinks the bulb has burnt out.
Solution The Extreme DRL solves all of these issues due to the smart circuitry built into the controller and superior thermal management. No scenario will create a failure from overheating or reduced load, triggering hyperflash. When the parking lights or DRLs are on, the output is reduced to a safe but very bright 700LM. When the turn signal is applied, the output doubles to 1400LM and draws just under 2A of current, which does not trigger hyperflash. The optional dimming wire triggers the output to the equivalent of a standard parking light.
Radial Lens As if the Extreme wasn't extreme enough, we decided to kick it up a notch. The original lens is not terrible by any means; we just saw an opportunity for even more output and ran with it. The ultimate goal when developing an LED replacement is to simulate the characteristics of the filament bulb. Not only does the Extreme have insane lumen levels, but all that power has been harnessed to fire perfectly in the lamp housing reflector. Combined with the two-position adjustable feature, this produces an intensity like no other LED on the market.
The Original For years, we have been innovating and pioneering the industry with products like the V3 and V6 systems. We've been there, done that, and have experience in designing a system that not only has the kinks worked out but performs better than anything else on the market. When quality comes into question, know you can trust VLEDS.
Highlights
- High-output driver with the best components available.
- 12X highest bin rating 2525 chips.
- 70LM Parking 900LM DRL 1400LM Turn - measured output per bulb
- The low parking or DRL circuit shuts off when the turn signal is applied for a more defined notification.
- Integrated HDRL controller senses DRL input and switches the output to 900LM.
- Dim amber option for parking light output with headlights on.
- 5X brighter than stock.
- Current Draw 2A @ 14.4V 27W
- No resistors required
FUSE TYPE
Convert your turn signals to an automatic daytime running light with this simple fuse tap and harness. This will activate the 900LM output whenever the ignition is switched on. Simply match your fuse type, and tap into a switched ignition circuit.
Wiring Diagram
1. Base Adapter
2. Resistor Plug (Not Used)
3. Controller
4. Dim Wire Harness (Optional)
5. V6 Extreme Bulb
6. DRL Harness
7. Fuse Tap
Warranty
This product comes with a 3-year warranty supported by VLEDS. We do not require the product to be shipped back to us. Improper product installation, as well as any system components or wiring modifications, will void all warranties. See our full Warranty Details for more details.
What's Included
2X - V6 Extreme Amber DRL Bulb
2X - V6 Extreme DRL Controller
2X - Adjustment Spacer
2X - V6 Base Adapter
2X - Single Pin Wire + Solo Tap (Dim Parking Output)
1X - DRL Wiring Kit
1X - 10-Foot Split Loom
2X - Sealing Gasket
2X - Adhesive Lined Heat Shrink
2X - Dielectric Grease Pack
2X - Collar
2X - Allen Key
2X - 8 Screw
| Base Number | 7507 |
|---|---|
| Series | V6 Extreme |
| Output (Each) | 900LM 1400LM |
| Current Draw @ 14.4V | 2A |
| Power (Watts) | 29W |
| Operating Voltage | 12-18V |
| Wire Type | PVC 80° C |
| Finish Type | Anodized |
| Light Source | 2525 Proprietary Chip |
| Chip Quantity | 9 |
| Driver Style | Constant Current |
| Material | 6061 Aluminum |
V6 EXTREME AMBER DRL INSTALLATION INSTRUCTIONS
ESTIMATED TIME TO INSTALL
- 30-40 MINUTES
TOOLS REQUIRED
- WIRE STRIPPERS
- RUBBING ALCOHOL
- RAG OR PAPER TOWELS
- HEAT GUN OR TORCH
DOWNLOAD
INSTALLATION GUIDE
1. Unpack all parts and familiarize yourself with the various components.
2. Connect the base adapter to the V6 Extreme Switchback Controller.
3. Connect the V6 bulb to the V6 Extreme Switchback Controller.
4. Look at the backside of the housing that the bulb is going into and determine the position and quantity of screws required.
5. Install the supplied spacer ring onto the V6 Extreme bulb. Adding the spacer moves the bulb back into the housing. Test one side with and the other without to find the best output.
6. For 7440/7443 applications: Install screws and tighten flush with the body. Do not overtighten.
7. For 7440/7443 applications: Install the small sealing gasket over the bulb as shown.
8. For 1157/1156 & 3156/3157 applications: The adapter collar is required for these base types. Line up the holes and loosely install the screws. Once all screws are installed, tighten until flush with the collar. Do not over tighten.
9. For 1157/1156 & 3156/3157 applications: Install the large gasket over the bulb as shown.
10. Twist and turn bulb into housing. Some force may be required. Adjustment of the screw pattern may also be needed if the bulb does not fit the keyhole pattern.
11. To verify polarity of the socket, turn on the parking or hazard lights and install the socket until the bulb turns on. Test all functionality. If the bulb does not work, flip the base adapter 180 degrees.
12. Apply dielectric grease to the contacts of the socket and slide the heat shrink over the adapter. Using a heat gun or torch, shrink the heat shrink over the base adapter and socket. Skip this for interior applications.
13. If hyperflash fix resistors were included with your kit, plug the VLR into the 2-pin wire on the base adapter.
14. Apply the provided high-temp mounting tape to back of the resistor. Find a clean metal surface and mount the resistor. Press firmly for about 30 seconds. Make sure no plastic or wiring is touching the resistor body.
15. If you would like the white LEDs to remain dim when the headlights are on, remove the white vinyl cap and plug in the dim wire. This will allow the white LEDs to dim down to 10% output with the headlights on. (See step 17 for wiring guide on dim wire)
16. If you want the LEDs to remain dim when the headlights are on, remove the black vinyl cap and plug in the dim wire. This will enable the amber parking light function when the headlights are on. (See next step)
17. Wiring for dim wire: Determine the positive 12V wire for the low beam headlight. Use the supplied tap to splice into the wire. You may need to strip some insulation to fit dimming wire into the tap. Skip this step if using the plug-n-play dim harness.
18. Before reassembling, ensure the entire system works properly with the engine running. Confirm there is no hyperflash.
© VLEDS INC.
Revision A | 7.1.24
Many online retailers sell standard off-the-shelf LED products, and the options can be overwhelming. Here are ten reasons you can trust us with your LED lighting needs.
1. Our Brand
We design and develop our products in-house. We are not a traditional reseller. We employ designers, mechanical engineers, and electrical engineers. Fitment, color, performance, and reliability are essential, allowing us to provide you with the best products possible.
We accept PayPal, Affirm, and all major credit cards.
2. Established Company
We've been in business for 19 years and have built an excellent reputation among automotive lighting enthusiasts. We are trusted and recommended by car and truck guys worldwide.
Life gets busy, so you've got time with our 60-day return policy.
3. Excellent Customer Service and Technical Support
We pride ourselves on offering first-class support to our customers. When you call or email us, you're talking to a person with years of knowledge and experience in the industry.
Same-day processing of replacement item by 2 pm PST. You are not required to ship the item back to us. See details HERE.
4. 25+ Years Combined Experience
Our staff is extremely knowledgeable and works firsthand with our products, from concept to installation. They know the ins and outs of every product we sell.
We make an LED replacement for nearly every bulb on your vehicle. We have several options and price points in many categories to meet your needs. Everyone has different tastes in color, so we offer up to 3 different kelvin ratings in our white LEDs, whereas the other guys only offer one.
5. Low-Cost, Flat-Rate Shipping
We have a fast, efficient pick-and-pack system with barcode scanning. Your order will be accurate and well-packaged for safe delivery to your door. Our shipping team provides you with order communication every step of the way.
Designed with the user in mind:
-
Simple navigation with a year make model bulb finder ensures you get the right part for your application
-
Clear and quality product photos so you know exactly what you're getting
-
Informational product descriptions
-
Specs and data on nearly every product
-
Install guides for the more complicated items
